HARD DRIVE FAULT TO DETECT OR BEEPING
If you've got ever closely-held your own pc then at
some purpose you've got had to contend with hardware that dies at
some purpose. typically many of us don't grasp what's even wrong,
however simply their pc quit operating and cannot begin.
interestingly enough, after you really attempt to begin the pc it
beeps many times and suddenly displays a message... "OS Not
Found".
Luckily for U.S. although, it’s really quite easy to exchange a
broken disk drive. Most of the time the sole tool you even want could
be a screw driver. Following these steps can enable you to exchange
that tough drive in no time flat! thus here they're...STEP TO AVOID FAULT DETECT OR BEEPING ON HARD DRIVE
- Disconnect the facility cable from the rear of the pc.
- Once you've got the facility disconnected, undo all the
opposite cables and wires from the pc.
- Place the pc tower on a table or stand to permit easier
access to the pc.
- Locate the 2 screws holding the duvet on the aspect of the
pc. Some computers, like Dell, have a handle or button you press
which will unharnessed the aspect of the pc for you while not having
to get rid of any screws.
- Remove the duvet and place off to the aspect, out of the
means.
- Unless you ordered over one disk drive for your pc, most
computers solely go with one disk drive. Most of the time they're
placed within the spot directly below your computer's compact disc
read-only memory or optical disk player. Older computers use IDE's
drives and newer computers use SATA drives. IDE is simple to
identify because it features a fairly wide cable attaching the disk
drive to the circuit board. SATA on the opposite hand, uses plenty
smaller cable. They each even have some type of power line hooked up
to them. this is often typically a tiny low, white plastic jack for
IDE, and a good smaller black jack for SATA. Once you recognize what
kind you've got you just have to be compelled to go purchase a
replacement disk drive that’s identical because the recent drive.
- At now you'll be able to disconnect the recent disk drive.
Don't disconnect the cables nonetheless.
- Install the new disk drive to the slot and screw it backtrack
properly.
- Once you've got the new disk drive in situ, disconnect the
primary cable from the recent disk drive.
- Attach this cable to the new disk drive.
- Disconnect the last cable and connect it to the new disk
drive.
- With each cables connected, you ought to be ready to replace
the duvet and screws to seal your pc case.
- Re-attach every cable to the rear of your pc, connecting the
facility cable keep a copy last.
- Install a recent copy of Windows on your pc and you ought to
be smart as new. Most computers go with some reasonably disk which
will install Windows for you. merely activate your pc, insert the
disk as shortly as you'll be able to, and it ought to show a message
asking you if you'd wish to boot from the CD. The Windows
installation is fairly easy subsequently.
And there are another case just similar with case above,
There is also each day after you boot your personal computer (pc) and you're welcome to the tune of a beeping pc with the words "INSERT SYSTEM DISK" show with black screen background or a range of that orthography. Likelihood is that the drive went below.
WHAT YOU MUST DO AND SOLUTIONS
And this is often what you're planning to do to induce around that and replace the drive. Initial you're planning to have to be compelled to take away the pc case. Either you've got a no tool needed pc case, or worst case state of affairs you're planning to want a screw driver. I cannot out right tell you ways to get rid of the pc case as there square measure thousands of various styles. However you'll manage to try to do it.
Next we'd like to spot if you've got a IDE or SATA that stands for Serial ATA. If the drive is connected there to massive board within the pc case (i.e. known as a motherboard), with a ribbon cable it's in all probability a IDE drive. you're planning to want a brand new one. Either get one from a conventional merchandiser or an internet merchandiser.
If the cable is spherical rather than a ribbon cable you've got a SATA drive. Therefore then you'd have to be compelled to either move to a conventional merchandiser or an internet merchandiser and obtain one amongst them. Next you're planning to have to be compelled to take away the recent drive and place within the new one. Secure it with no matter latching mechanism your pc case has with either screws or a tab feature. Connect the cable be it a ribbon cable or a spherical SATA cable.
Then you'll install the package. we have a tendency to square measure running on associate degree assumption that your pc can attempt to boot from the package disc if there's one in your read-only memory or DVD-ROM drive.
If not, build an effort to enter BIOS because there ought to be directions on a way to enter this configuration screen once your pc is booting and choose read-only memory as the initial boot device and save the settings and take a look at once more.